Pressure Washing Tips, Tricks, and Techniques

HEO-3004-0E8G
Pressure Washer
  • Before pressure washing make sure to always fog or presoak the surface with a detergent, degreaser, or chemical presoak. Presoaking reduces wash time and chemical cost.
  • Hot water is a better solvent than cold water.
  • Always rinse detergent off the surface before it dries.
  • Commercial contractors generally use 4 to 6/gpm at 1500 to 3,500/psi for most cleaningapplications. An exception to this is wood cleaning. Here 500 to 2,000/psi is preferred with chemical cleaning to reduce the furring of the wood. Water flow rates of less than 4 gallons per minute – found on general consumer (homeowner) units – are not high enough to be competitive because of increased cleaning time, which raises labor costs.
  • Chemical dilution is largely a matter of personal preference. For most mobile power washing work, chemical costs run from three to five percent of gross sales, labor accounts for 30 to 45 percent, and fuel for heat is two to four percent. If chemicals and heat costs are reduced, labor costs increase because of increased work time. A slight increase in chemical and fuel costs actually reduces labor costs, because work time decreases.  Work smarter – soap and heat are cheaper than labor – not harder.
  • Washers with chemical injection before the pump, start out with the metering valve open 1/4 turn. Then adjust as needed.
  • W-200 Spray Wax is similar to spray wax used in coin-operated car washes. Apply the wax hot and follow with a cold rinse for fine surfaces like cars and pickups. On heavier surfaces, like homes and trailers, the cold rinse is not necessary. The application of wax extends the life of the wash job, makes subsequent cleaning easier, and enhances the overall appearance. Note: Because the application of wax will extend the life of a wash job, some contractors choose not to use it because they prefer to wash more often. Thereare two sides to this. While the use of wax may reduce your income because of the extended life of your cleaning, the enhanced appearance and extended life may generate more business because of the perceived quality of the work.
  • For fleet washing, wax in the rinse water reduces dirt adhesion and lessens subsequent washing time. In heavy concentrations, wax reduces cement adhesion on concrete trucks.
  • The tips provided in this section will reduce brushing to about five percent of the total workload. Typically, contractors only brush in the spring or the fall, or as needed.
  • Brushing once or twice per year at a specified time allows the contractor to prepare and schedule extra, short-term, help for those designated times.
  • For Environmental Power Washing Techniques read Report 507.

 

Generators Residuals

Gasoline Generator GEN-13000-1MSE

Take Control of the Situation

The next time a severe storm rolls through the area, don’t be left in the dark, without the ability to cook, heat water, do laundry, or keep your family happily occupied. Instead, be prepared with the purchase and installation of a cost-effective residential generator from the knowledgeable professionals at GraciHart Electric. No longer will you and your family be uncomfortable and bored during power outages. Our line of residential generators power on automatically in the event of an outage, and operate quietly and dependably for days, some models can even operate, uninterrupted for weeks. If you prefer, we can elevate the equipment above flood lines. Another notable advantage to installing a generator for home use is that in the event of an electrical power outage your home’s security system will remain functional, keeping your family and property safe and sound.

The next time your neighborhood loses power during a thunderstorm, don’t let another outage inconvenience you and your loved ones. Call on GraciHart Electric and let us help you choose a residential generator that will meet all of your emergency power needs.

Service Question of the Day!?

1f1e2ed3de9b25f9d79ef733cbc4c83c

Describe the most common types of jobs you do for your clients.

We service on industrial equipment, water reclamation, oil water separators, closed loop water treatment systems, car wash equipment, waste water evaporators, wash water evaporators, generators, pumps, hot water power washer, construction equipment, soaps, chemicals, degreases, bioremediation products, & hot & cold pressure washer parts rentals repairs.

Generator Fun Facts

Portable Generator
Portable Generator

–If you actually want to plug something in to your generator which lives more than 20 feet away, prepare to spend as much on heavy gauge power cords as you would for yearly passes to the water slide park for a family of four.

 

–They are every bit as heavy as you feared. Luckily, they have wheels. This is when you’ll discover that the place you want to put your generator does not have pavement.

 

–You apparently need about a million watts of generator capacity if you plan on actually using a major appliance–like, say, your electric razor. That’s because–at least according to the “sizing charts” that accompany generators–even the most innocuous appliances are given to wild streaks when–like the Hulk when you make him angry–they surge to 20 times their original power. That fridge you’ve been monitoring at 22 watts all year? According to lore, it can surge up to 1750 watts when something (the defroster?) sets it off. Consider yourself warned.

 

–GFCI outlets and computers don’t mix. This is the big one, and really the whole excuse for writing this post. You see, a GFCI outlet (Ground Fault Circuit Interrupter) is standard on most portable generators, and is used to make sure you don’t kill yourself by taking the genny with you as you take a quick dip in the pool. The idea is, if it ever sees even a tiny disparity in the generated power vs. What it senses on the neutral wire, it’ll throw the breaker so that your loved ones will be safe as they fish your body out of the shallow end.

Pressure Washing Techniques

Hot Water Pressure Washers
Hot Water Pressure Washers
  • When pressure washing always fog or presoak the surface with a detergent, degreaser, or chemical presoak. Presoaking reduces wash time and chemical cost.

  • Hot water is a better solvent than cold water.

  • Always rinse detergent off the surface before it dries.

  • Commercial contractors generally use 4 to 6/gpm at 1500 to 3,500/psi for most cleaning applications. An exception to this is wood cleaning. Here 500 to 2,000/psi is preferred with chemical cleaning to reduce the furring of the wood. Water flow rates of less than 4 gallons per minute – found on general consumer (homeowner) units – are not high enough to be competitive because of increased cleaning time, which raises labor costs.

  • Chemical dilution is largely a matter of personal preference. For most mobile power washing work, chemical costs run from three to five percent of gross sales, labor accounts for 30 to 45 percent, and fuel for heat is two to four percent. If chemicals and heat costs are reduced, labor costs increase because of increased work time. A slight increase in chemical and fuel costs actually reduces labor costs, because work time decreases.  Work smarter – soap and heat are cheaper than labor – not harder.

  • Washers with chemical injection before the pump, start out with the metering valve open 1/4 turn. Then adjust as needed.

  • W-200 Spray Wax is similar to spray wax used in coin-operated car washes. Apply the wax hot and follow with a cold rinse for fine surfaces like cars and pickups. On heavier surfaces, like homes and trailers, the cold rinse is not necessary. The application of wax extends the life of the wash job, makes subsequent cleaning easier, and enhances the overall appearance. Note: Because the application of wax will extend the life of a wash job, some contractors choose not to use it because they prefer to wash more often. There are two sides to this. While the use of wax may reduce your income because of the extended life of your cleaning, the enhanced appearance and extended life may generate more business because of the perceived quality of the work.

  • For fleet washing, wax in the rinse water reduces dirt adhesion and lessens subsequent washing time. In heavy concentrations, wax reduces cement adhesion on concrete trucks.

  • The tips provided in this section will reduce brushing to about five percent of the total workload. Typically, contractors only brush in the spring or the fall, or as needed.

  • Brushing once or twice per year at a specified time allows the contractor to prepare and schedule extra, short-term, help for those designated times.

  • For Environmental Power Washing Techniques read Report 507.

Pressure Washer Tips!

Pressure Washing
Pressure Washing

Here are a few maintenance tips for your pressure washer that could save you some money:

  • Always make sure when using the washer to keep the trigger gun open and do not open and close the trigger repeatedly. This causes premature wear of the unloader.
  • Make sure and check your nozzle. Surprisingly it is most often the least expensive and easiest way to get your pressure up. Make sure and use the right one for your specific washer or you can do damage to the pump.
  • Cool it down. I know that this is repeated often but it worth repeating. Not cooling the washer down before turning it off expands the coil and can cause premature failure over time. It also causes premature wear on the pump seals and packing’s.
  • Use a downstream injector on your washer. Do not run soap through the coil and pump. Soap salesman love to tell you it is the best way. It is for them. We also get more repairs. Use soap downstream of the washer. It is a $50.00 item that can save you a lot of money

Welcome!! Construction Equipment

Clean Rite Equipment & Environmental has been serving Louisiana, as well as other parts of the Gulf Coast, since 1997.

What started out as a one-man pressure cleaning company has turned into much more. As a dealer of Mi-T-M, Wacker, KO Manufacturing, Magnum, and other top of the line brands, we take our business seriously, because we know our customers depend on us. Unlike many of the other dealerships in our region, we also provide preventative maintenance, warranty service work, & repair for your equipment & machinery, which means we usually have parts in stock as well.

Plus, our Equip-Worx division handles the heavy stuff when it comes to small gas & diesel engine equipment & machinery.

We sell, service and rent the following:
construction equipment,
pumps,
environmental equipment,
hot and cold water pressure washers,
gas saws,
rammers,
walk behind and ride on trowels,
gas and diesel generators,
diaphragm pumps,
oil water separators,
closed loop water system,
chemicals,
car wash systems,
and other specialty equipment
If you’re in need of excellent equipment, affordable rentals, or repair service, come see us! We’ve got you covered.

Give us a call (504) 468-7997 or come by and see us at 1332 Fulton St. Kenner, LA 70062. Our regular business hours are 7:30 am – 4:30 pm Monday – Friday. We look forward to doing business with you!