Understanding PSI (Pounds per Square Inch)-Pressure Washer

OLYMPUS DIGITAL CAMERA

Water pressure from the pressure washer is measured in pounds per square inch or psi. This pressure is the amount of force delivered to the surface being cleaned, and is the critical factor in breaking debris from that surface. PSI is determined by the orifice size of the nozzle tip and the flow rate (gallons per minute). For labeling purposes, the standard nozzle size for measurement is a #4 orifice, which delivers 4.0/gpm at 4,000psi. As nozzle sizes increase or decrease, psi fluctuates accordingly.  The nozzle chart in our catalogue lists the psi with different flow rates and nozzle sizes. Nozzle selection depends on the work, and the amount of pressure a surface can withstand before it is damaged.

While psi is a constant at the tip of the nozzle, the pressure decreases as its distance from the targeted surface increases. Experienced power wash contractors understand how to manipulate these distances for maximize both cleaning power and their time.

Because the pressure that contractors need varies a great deal, they get the most out of their equipment by adjusting the distance between the nozzle and the surface being cleaned. For less pressure and heat in the application, they hold the nozzle back, thereby increasing the distance from the surface. For increased pressure and heat, they hold the nozzle closer. Larger contract cleaners will use pressure washers that produce 4 to 6 GPM at 3,000 to 3500 psi at 200⁰ F for concrete cleaning. Vehicle washing can be accomplished using 1,500 to 2,000 psi.

Heat provides a tremendous advantage when cleaning grease and oil. A few Vent-a-Hood cleaners will use steam heated to 310⁰ F, while others will use units that deliver 3,000psi at 200⁰ F. However, some vent cleaners use electric, 1,000 PSI cold water washers hooked up to hot water (they must hand scrape more for this to be effective).

The psi for decks and other wood surfaces varies from 200 to 3,000, and must be carefully tested first, as too much pressure will cause the wood to fur. If this happens, you will need to sand the affected areas with fine sand paper or steel wool to knock off the furred surface. Many professional deck cleaners use a variable pressure wand (like the ST-54 36″ Double Lance Wand) so they can adjust the pressure as necessary. Using low pressure, and letting the chemical (like Powerwash.com’s DSR-49 Deck and Siding Restorer or DSR-50 Deck and Siding Restorer plus Stripper) do the work helps avoid furring. Test the effect of pressure on the underside of the deck.

Service Question of the Day!?!!

customer-service

What do you wish customers knew about you, your service, or your profession?

 I wish that our customers knew how much work we put into each and every one of their machines to ensure that when we are done it leaves here working in just as good condition as we promised it would. Their business means a lot to us as a small growing company, and so before attempting to buy their machines or get them serviced on by someone else to give us a chance first. We promise to give the best deal financially possible for all of our customers.

Pressure Washing Tips, Tricks, and Techniques

HEO-3004-0E8G
Pressure Washer
  • Before pressure washing make sure to always fog or presoak the surface with a detergent, degreaser, or chemical presoak. Presoaking reduces wash time and chemical cost.
  • Hot water is a better solvent than cold water.
  • Always rinse detergent off the surface before it dries.
  • Commercial contractors generally use 4 to 6/gpm at 1500 to 3,500/psi for most cleaningapplications. An exception to this is wood cleaning. Here 500 to 2,000/psi is preferred with chemical cleaning to reduce the furring of the wood. Water flow rates of less than 4 gallons per minute – found on general consumer (homeowner) units – are not high enough to be competitive because of increased cleaning time, which raises labor costs.
  • Chemical dilution is largely a matter of personal preference. For most mobile power washing work, chemical costs run from three to five percent of gross sales, labor accounts for 30 to 45 percent, and fuel for heat is two to four percent. If chemicals and heat costs are reduced, labor costs increase because of increased work time. A slight increase in chemical and fuel costs actually reduces labor costs, because work time decreases.  Work smarter – soap and heat are cheaper than labor – not harder.
  • Washers with chemical injection before the pump, start out with the metering valve open 1/4 turn. Then adjust as needed.
  • W-200 Spray Wax is similar to spray wax used in coin-operated car washes. Apply the wax hot and follow with a cold rinse for fine surfaces like cars and pickups. On heavier surfaces, like homes and trailers, the cold rinse is not necessary. The application of wax extends the life of the wash job, makes subsequent cleaning easier, and enhances the overall appearance. Note: Because the application of wax will extend the life of a wash job, some contractors choose not to use it because they prefer to wash more often. Thereare two sides to this. While the use of wax may reduce your income because of the extended life of your cleaning, the enhanced appearance and extended life may generate more business because of the perceived quality of the work.
  • For fleet washing, wax in the rinse water reduces dirt adhesion and lessens subsequent washing time. In heavy concentrations, wax reduces cement adhesion on concrete trucks.
  • The tips provided in this section will reduce brushing to about five percent of the total workload. Typically, contractors only brush in the spring or the fall, or as needed.
  • Brushing once or twice per year at a specified time allows the contractor to prepare and schedule extra, short-term, help for those designated times.
  • For Environmental Power Washing Techniques read Report 507.

 

Pressure Washing Techniques

Hot Water Pressure Washers
Hot Water Pressure Washers
  • When pressure washing always fog or presoak the surface with a detergent, degreaser, or chemical presoak. Presoaking reduces wash time and chemical cost.

  • Hot water is a better solvent than cold water.

  • Always rinse detergent off the surface before it dries.

  • Commercial contractors generally use 4 to 6/gpm at 1500 to 3,500/psi for most cleaning applications. An exception to this is wood cleaning. Here 500 to 2,000/psi is preferred with chemical cleaning to reduce the furring of the wood. Water flow rates of less than 4 gallons per minute – found on general consumer (homeowner) units – are not high enough to be competitive because of increased cleaning time, which raises labor costs.

  • Chemical dilution is largely a matter of personal preference. For most mobile power washing work, chemical costs run from three to five percent of gross sales, labor accounts for 30 to 45 percent, and fuel for heat is two to four percent. If chemicals and heat costs are reduced, labor costs increase because of increased work time. A slight increase in chemical and fuel costs actually reduces labor costs, because work time decreases.  Work smarter – soap and heat are cheaper than labor – not harder.

  • Washers with chemical injection before the pump, start out with the metering valve open 1/4 turn. Then adjust as needed.

  • W-200 Spray Wax is similar to spray wax used in coin-operated car washes. Apply the wax hot and follow with a cold rinse for fine surfaces like cars and pickups. On heavier surfaces, like homes and trailers, the cold rinse is not necessary. The application of wax extends the life of the wash job, makes subsequent cleaning easier, and enhances the overall appearance. Note: Because the application of wax will extend the life of a wash job, some contractors choose not to use it because they prefer to wash more often. There are two sides to this. While the use of wax may reduce your income because of the extended life of your cleaning, the enhanced appearance and extended life may generate more business because of the perceived quality of the work.

  • For fleet washing, wax in the rinse water reduces dirt adhesion and lessens subsequent washing time. In heavy concentrations, wax reduces cement adhesion on concrete trucks.

  • The tips provided in this section will reduce brushing to about five percent of the total workload. Typically, contractors only brush in the spring or the fall, or as needed.

  • Brushing once or twice per year at a specified time allows the contractor to prepare and schedule extra, short-term, help for those designated times.

  • For Environmental Power Washing Techniques read Report 507.

Welcome!! Construction Equipment

Clean Rite Equipment & Environmental has been serving Louisiana, as well as other parts of the Gulf Coast, since 1997.

What started out as a one-man pressure cleaning company has turned into much more. As a dealer of Mi-T-M, Wacker, KO Manufacturing, Magnum, and other top of the line brands, we take our business seriously, because we know our customers depend on us. Unlike many of the other dealerships in our region, we also provide preventative maintenance, warranty service work, & repair for your equipment & machinery, which means we usually have parts in stock as well.

Plus, our Equip-Worx division handles the heavy stuff when it comes to small gas & diesel engine equipment & machinery.

We sell, service and rent the following:
construction equipment,
pumps,
environmental equipment,
hot and cold water pressure washers,
gas saws,
rammers,
walk behind and ride on trowels,
gas and diesel generators,
diaphragm pumps,
oil water separators,
closed loop water system,
chemicals,
car wash systems,
and other specialty equipment
If you’re in need of excellent equipment, affordable rentals, or repair service, come see us! We’ve got you covered.

Give us a call (504) 468-7997 or come by and see us at 1332 Fulton St. Kenner, LA 70062. Our regular business hours are 7:30 am – 4:30 pm Monday – Friday. We look forward to doing business with you!